Global Organization
Liu L, et al. Performance evaluation of a novel solar photovoltaic–thermal collector with dual channel using microencapsulated phase change slurry as cooling fluid. Energy Convers Manag. 2017;145:30–40.
Wang Z, et al. Photo-thermal performance evaluation on MWCNTs-dispersed microencapsulated PCM slurries for direct absorption solar collectors. J Energy Storage. 2019;26:100793. Liu J, et al. Preparation of graphite nanoparticles-modified phase change microcapsules and their dispersed slurry for direct absorption solar collectors.
Nature, 155, 364-365. Delgado, M., Lázaro, A., Mazo, J., MarÃn, J. M., Zalba, B. (2012). Experimental analysis of a microencapsulated PCM slurry as thermal storage system and as heat transfer fluid in laminar flow.
Given that micro- and nano-encapsulated phase change material slurries are very useful in the fields of thermal storage and heat transfer, due to their influence on the heat capacity of fluid, these materials have lots of applications.
Zhang G, et al. An experimental investigation of forced convection heat transfer with novel microencapsulated phase change material slurries in a circular tube under constant heat flux. Energy Convers Manag. 2018;171:699–709.
The improvement of solar collectors has always been a significant issue for solar filed researchers. By converting the indirect absorbent solar collectors into direct forms, the problems of heat loss are solved partially. However, in direct absorbent solar collectors (DASC), the fluid must encompass the high capability of heat absorption.
Silicon Heterojunction Solar Cells; Low-temperature carrier selective contacts for silicon solar cells ... step (see Figure 3 and 4). In addition, the transition from slurry to diamond wire sawing also inspired some companies to investigate ...
This experimental study reports on the performance of maintaining low PV temperatures with front-surface water-cooling and back-surface cooling with a PCM based …
November Solar News: China''s reduction in photovoltaic export tax rebates may lead to an increase in module prices, with current solar panel prices in Europe below 6 cents per watt. France plans to install about 1.35 GW of solar …
The possibility of operating the collector at lower average temperatures, but still providing a satisfactory enthalpy flux with reasonable mass flow rates, makes it possible to …
In the present work, some of the thermo-physical and rheological properties and material behaviour that interest flat-plate solar thermal collectors with slurry PCM as the heat …
It was concluded that the PV temperature can be reduced up to 21% and the thermal and electrical efficiencies are 78.5% for MPCMs and 71.9% for water, at 18:00 which …
A Matlab/Simulink based model has been developed to predict the instantaneous solar radiation intensity, the outlet temperature of collector working fluid, the tank temperature …
Semantic Scholar extracted view of "Potentialities of a Low Temperature Solar Heating System Based on Slurry Phase Change Materials (PCS)" by Gianluca Serale et al.
A Matlab/Simulink based model has been developed to predict the instantaneous solar radiation intensity, the outlet temperature of collector working fluid, the tank temperature …
Photovoltaic generation is a temperature-dependent technology, with each 1 °C temperature rise of the PV module, the efficiency drops by 0.2–0.5 % depending on the material of the PV...
The test temperature represents the average temperature during the solar peak hours of the spring and autumn in the continental United States [1]. According to the …
A low-temperature slurry for a heterojunction photovoltaic cell is prepared from the following raw materials in percentage by weight: 40-80% of micron-sized silver-coated copper powder, 15 …
The outcomes also revealed that as the serpentine piping diameter enhanced, the slurry''s flow rate improved, reducing the PV cells'' temperature, thereby augmenting the …
Currently, the mPCM slurry is used as a working fluid for cooling photovoltaic panels [17,18,19,20,21,22]. It is shown that it is possible to receive significant amounts of heat from …
The possibility of operating the collector at lower average temperatures, but still providing a satisfactory enthalpy flux with reasonable mass flow rates, makes it possible to …
Thermo 2022, 2 385 Thermo 2022, 2, FOR PEER REVIEW 3 (a) (b) Figure 1. Configuration of the PV/JIC system. (a) Schematic diagram and (b) nozzle arrays. Table 1.
Currently, the mPCM slurry is used as a working fluid for cooling photovoltaic panels [17,18,19,20,21,22]. It is shown that it is possible to receive significant amounts of heat from …
Photovoltaic generation is a temperature-dependent technology, with each 1 °C temperature rise of the PV module, the efficiency drops by 0.2–0.5 % depending on the …
In view of this, the researchers developed a photovoltaic/thermal (PV/T) system that enables continuous supply through active cooling technology to keep PV module temperatures low. …
Download Citation | On Jun 1, 2023, S. Li and others published Thermodynamic analysis of photovoltaic/thermal heat pump based on phase change slurry | Find, read and cite all the …
A testing rig is constructed consisting of two identical heat pipe solar PV/T cogeneration systems A and B, in which water and 30% alkyl hydrocarbon PCS are, respectively, employed as …
@article{Chen2020ExperimentalSO, title={Experimental study on characteristics of a nano-enhanced phase change material slurry for low temperature solar energy collection}, …